Our company manufactures and supplies a wide range of Length Comparator & Cement Autoclaves, which is used to measure the drying shrinkage of concrete autoclave expansion of portland cement and potential expansive reactivity of cement aggregate combinations in mortar bars during storage, on self drying. It is equipped with gauging trowel and fitted with wooden handle.

Specifications:

Determination of Soundness By Means Of Autoclave Test

ASEW-145

• Length Comparator: IS: 4031 Consists of a frame with adjustable cross plate and a recessed seating and a stainless steel reference bar with 6 mm dia balls mounted at the ends Supplied complete with a dial gauge 0.002 mm. 
  

• Cement Autoclave for a high pressure steam as per IS:4031,ASTMC151.
• Consists of a stainless steel cylinder with an insulated cover. Mounted on a sturdy supporting frame, enclosed in a heat insulating metal housing. The attached control unit enclose a sensitive pressure regulator and pressure gauge, power switches and pilot lamps for controlling the electric heating unit. Inside chamber size; 15 cms dia x 60 cm height.
  

  
  ASEW-147

  • Laboratory Cement Autoclave, with Electronic Digital Readout for Pressure & temperature. 
    

  
  ASEW-148

  • Gauging Trowel
  • Fitted with wooden handle.

  
  ASEW-149

  • Shrinkage bar mould, IS: 10086, IS: 4031,BS 1377 with base plate & two reference points
    

  
  ASEW-150

  • Shrinkage bar mould with two mould compartment on a single base.
    

  
  ASEW-151

  • Shrinkage Bar mould with three compartment on a single base.
    

  
  ASEW-151(A)

  • Shrinkage bar mould with four mould compartment.

We are a renowned manufacturer and supplier of Vibrating Machines (cement mortar cube vibrator. The vibrator of our range is mounted over coiled springs and the vibrations are developed by means of a revolving eccentric shaft. Further, the simple design of our machine facilitates easy assembly and dismantling of the cube molds.

Specifications:

Heat of Hydration

• ASEW-152
• Calorimeter : IS : 4031, BS 4550,ASTM C186for Heat of hydration of Cement. Consists of : A open mouthed thermos flask, Beckman Thermometer, Insulating material, Container, Hinge, Stirring Motor, thermometer support, Glass stirring rod, Cork stopper, Reading Lens and glass Funnel.
  

  
  ASEW-152

  • VIBRATING MACHINE: IS: 10080, BS 4550 Consists of a frame mounted on coil springs to carry the cube mould , and a revolving shaft provided with an eccentric.
  • By means of a balance weight beneath the base plate attached rigidly to the frame, the center of gravity of the whole machine, including the cube and mould, is brought either to the eccentric shaft, or within a distance 25mm below it.
  • Normal running speed of eccentric shaft is 12,000±400RPM. Fitted with BELT GUARD. The motor and a crowned pully on the vibration machine.
  • Supplied complete with one cube mould 7.06 cms with base plate. Suitable for operation on 230 V, single phase, 50 cycle, A.C. supply Complete with timer.
    

    
    ASEW-153

    • Vibrating machine with Digital timer.
      

    
    ASEW-154

    • Pocking rod. Spares:
    • Belt
    • Set of Springs
    • Belt guard
    • Cube Mould, steel 7.06 cms with base plate
    • Time switch 0-5 minute.

We are offering Mortar Mixers, which is used for mixing cement pastes, mortar and pozzolanas. The mixer consists of an epicyclic type stainless steel paddle imparting both planetary and revolving motion and it has two speeds.

Specifications:

ASEW 155

• Mortar Mixer (Mixing Apparatus): IS : 4031; IS : 10890, BS 3892
• Mixer Blade Planetary movement Rev/min rev/min
• Low speed 140 ± 5RPM & Plantry 62 ± 5RPM
• Medium speed 285±10RPM& Plantry 125±10
• Stainless steel Bowl fitted with handle. It shall be provided with a lid made of non-absorbing material and not attacked by cement, masonry cement, cement Pozzolana mixture or lime Pozzolana mixture.
• Scraper-The scraper consists of a semi-rigid rubber blade attached to a handle about 150 mm long. The blade about 75 mm long, 50mm wide and tapered to a thin edge. Suitable for operation on 230volts, single phase, 50 cycle, A.C. supply
  

  
  ASEW-156

  • Jolting apparatus : IS: 4031 ,IS 10078,BS 3892 The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at horizontal distance of 800 mm from the center of the table.
  • The table can be raised and allowed to fall freely by a com stroke counter fitted with micro-switch is provided which stops the machine after 60 jolts. Locating pins are provided for mounting the mould compartment on the table.
  • The mould surrounded by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Operation on 230V, single phase, 50 cycle, A.C. Supply.
    

    
    Soundness of Cement & Hydrated Lime

    ASEW-157
    

    • Le-chatelier mould complete with two glass plate and one lead weight IS: 4031, IS:5514,BS 6463-44.
      

    
    ASEW-158

    • Le-Chatelier Flask for Specific Gravity test IS : 4031.
      

    
    ASEW-159

    • Le-Chatelier Water Bath with rack for holding Moulds. Fitted with Thermostat.
      

    
    ASEW-160

    • Water Retension Test: IS :4031
      

    
    ASEW-161

    • Cement Spatula : IS : 269; BS:12 for the preparation of tensile Specimens.
      

    
    ASEW-162

    • Gauging Trowel : IS : 4031; BS: 12 fitted with wooden handle.

    
    Determination Of Strength Of Cement And Mortar

    ASEW-163
    

    • 400 kg (4 Kn) Flexure Testing machine, electrically operated. Complete with flexure attachment. Proving Ring of 400 kg. Capacity. Operation on 230 Volts, single phase, 50 cycle, A.C. supply.

Our company offers a wide range of Concrete Mixer & Vibrators, which is a commonly used apparatus for preparing a homogeneous mixture of various materials like cement, sand, gravel and mainly used in the construction industry. These are suitable for operation on 440 volts, 3 phase, 50 cycle A.C. supply.

Specifications:

ASEW-164

• Concrete Mixer, Laboratory Model, Motorised: Light weight Laboratory Concrete mixer is designed to remove the burdensome work of hand mixing Uniform, thoroughly mixed batches can be produced in the field or laboratory.
• The counterbalanced mixing drum is easy to tilt. Two cubic feet mix capacity. Total drum volume is 2 cubic feet. Mounted on a sturdy rubber tired stand. Drum is mounted for end discharge. Equipped with end towing pole.
• Suitable for operation on 440 volts, 3 phase, 50 cycle A.C. supply.
  

  
  ASEW-165

  • Concrete Mixer, Laboratory Model: Hand.

  
  ASEW-166

  • Needle Vibrator :ASTMC 403 The laboratory Needle vibrator is used in vibrating concrete test cylinder and beams in the field or laboratory.
  • It is also widely used in making laboratory specimens, in making concrete products, in experimental work, and in small scale construction projects.
  • The vibrator is electrically driven and is easily controlled.
  • The vibrating pin is 350 mm long and 25mm in dia. Flexible shaft is 1.5 mtr or 4 meter Long. Vibrating speed is approx. 10,000 rpm. Powered by a 1 H.P electric motor. Operation on 440 Volts, 3 phase, 50 cycle, A.C. supply.

  
  ASEW-167

  • Needle Vibrator, same as per ASEW-166, but vibrating pin is 350 mm long and 40 mm dia.
    

  
  ASEW-168

  • Needle Vibrator, same as per ASEW-166, but vibrating pin is 350 mm long and 40mm dia with 3 meter long flexible shaft.
    

  
  ASEW-169

  • Cement Tensile testing machine. Manually operated, BS : 12 IS : ^269. Capacity 500 kg. Complete with one briquette mould and set of weights to weigh 50,100,150 and 200 kg. Without lead shot. Accessories:
  • Lead shot 5 kg bag.
  • Briquette Mould, made of Gunmetal with steel plate.
     

  ASEW-170
  

  • Cement Tensile testing machine, motorized. Capacity900kg, BS: 12;IS:269 The sliding weight and the lever ratios have been so fixed that the load applied to the test briquette. The load is read directly from the scale engraved on the top lever, using the vernier attached to the sliding weight. Suitable for operation on 230 volts, single phase, 50 cycle, A.C. supply Complete with one base plate.
    

  
  ASEW-171

  • Brazilian Test Apparatus:
  • It is for conducting Brazilian test on 75mm dia x 25 mm thick samples and can be used for compression tests on 70.6 mm cement mortar cubes also. Comprises a hand operated hydraulic jack provided with self retracting piston fixed on the base of a load frame Loads are recorded on a pressure gauge 0-5 tonne x 25 kg and a maximum pointer is provided for the breaking load indication. Semi-cylindrical loading strips are provided for Brazilian test and two hardened and ground platens are provided for compression test.

We are offering Permeability Testers, which is frequently used for testing permeability of cement mortar and concrete specimens in laboratories. It finds wide application in ceramic, cement and concrete industry. These permeability testers secure a fast, accurate and user-friendly permeability testing.

Specifications:

ASEW-172

• Permeability Tests: IS : 1727; IS : 1645 : Consists of: Specimen container ring of 100 mm diameter and50 mm high, held between a bottom plate and a water cell. The Water cell of 100 mm diameter brass cylinder and the top and bottom
• Plates of brass or any other non-corroding metal. Each cell with collar is clamped in between a base plate and a top plate with the help of tension rods and nuts.
• The cell assembly is mounted on the stand. The top plate is provided with an inlet and air release vent and the base plate is provided with an outlet. Complete with a pressure chamber is fitted with a pressure, and a pressure gauge 0-10 kg/cm2 indicating the chamber pressure,
• Three Cell Model with Air compressor.
•  Six Cell Model with Air compressor.

Our company is engaged in manufacturing and supplying a wide range of Air Permeability Apparatus, which is used for determining the fineness of cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement. It includes spares such consistency plunger, initial needle and final needle.

Specifications:

Fineness

ASEW-174

• Blain Air Permeability Apparatus IS : 4031, IS :
• 5516, ASTMC204,BS:4359part2
• The apparatus comprises one each of Permeability Cell, 'U' tube tube manometer with stop cock on a sunmica wooden stand, perforated metal disc, plunger. Rubber stopper, Rubber tube with rubber bulb.
  
• Dibutylphthalate liquid. (500 gram bottle).
• Punch.
• Spares:
• Sunmica wooden stand with 'U' tube manometer with stop cock.
• Permeability Cell complete with perforated metal disc, non-perforated disc and plunger.
  

  
  ASEW-175

• Accessories:
  

• Air Permeability Apparatus (Lea & Nurse type) IS 5536,IS:4825
• The equipment comprises one each of Air permeability Cell complete with perforated plate and compacting plunger, stand fitted with manometer and capillary tube. Complete in a nice wooden carrying case.
  

  
  Accessories :

  Filter paper disc cutter.


Consistency and Setting Time

ASEW-176

• Vicat Needle apparatus, IS : 5513, IS:2542(part-2),2645,1727, BS: 12,146,915,1370,4027,4246, 4248, ASTM C-91, C-141, C-187, C-308, C-359, C-472 & AASHTO T-129, E-131.
• Consists of a metallic frame bearing a movable rod with cap at one end and a vicat mould 70 mm in dia at the base, 50 mm at the top and 40 mm high and with a glass base plate.
• Consistency plunger, initial and final needles in a nice jewellery case.
• Vicat Needle Apparatus with Dash pot. Similar to ASEW-176, but fitted with dashpot to facilitate the gentle lowering of the needle.
  

  
  Spares:

• Consistency plunger.
• Initial Needle.
• Final Needle.
• Vicat mould made of gunmetal.
• Jewellery box.
  

  
  ASEW-178

• Vicat Apparatus, Modified: IS: 2545 (Part-I) Functions both as a standard Vicat Apparatus and modified Vicat apparatus. It is used for determining the normal consistency of hydraulic cement, gypsum plaster and lime, and the setting time of hydraulic cement, gypsum plaster & gypsum concrete. Supplied complete with a needle,, three plungers and a brass weight.
  

• Gillmore Needle apparatus : ASTM C-91, C-14I, C-266, C-414.
• For determining setting time hydraulic cement.
• The apparatus consists of a base with a vertical shaft and two horizontal arms, the lower arm being adjustable of height. Supplied complete with one initial needle, one final needle and a glass bade plate.
  

  
  ASEW-180

• Southard Viscometer: IS: 6932 Part VI) For adjusting the consistency of lime putty mixture. Consists of a metal cylinder of 500 mm internal diameter, mounted over a wooden plate form. A close fitting piston with a working stroke of 65 mm moves up and down without rotation inside the cylinder. A metal bridge measures the degree to which the ejected cylinder of putty has slumped. Complete with one lime putty density vessel.

Our range of Flow Table is a multi-purpose table designed for determining the flow of concrete cement. It is also available as hand-operated and electrically operated types. These are catering to the requirements of diverse applications such as cement plants, building construction, aggregate & concrete testing and mining.

Specifications:

Flow and Workability of Mortars And Lime

ASEW-182

• Flow Table, Manually operated
• IS:5512.BS:4551-1,ASTMC230
• The Flow Table consists of a brass table top 250±2.5 mm dia mounted on a rigid stand. The table top is re-inforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardned cam.
  

  
  ASEW-183

  • Flow Table, Motorized
  • Same as ASEW-182 but cam shaft is rotated at the rate of 100 r.p.m. by an electric motor. Suitable for operation on 230 Volts, 50 cycles, single phase, A.C. Supply.
  • Spares:
  • Flow Mould.

   

  Flow of Building Limes

  ASEW-184
  

  • Flow Table: IS 6932 (Part VIII) Consists of a steel table top 300 mm dia ground and polished with three inscribed annular circles 70, 110 and 190 mm dia arranged by cam action have a free fall of 12.5 mm. Complete with conical mould 65mm dia of larger end, 40 mm dia of narrow end and 90 mm high.