Our range of Abrasion & Flexural Strength Testing Machine is manufactured and supplied complete with a tray for collection of the material. It consists of set of 12 Nos cast iron spheres or steel spheres (hardened steel balls) approximately 48 mm in diameter, each weighing between 390 - 445 grams.

Specifications:

ASEW-191

• Los Angles abrasion testing machine : 2386 (P-IV),ASTMC131,C535
• Consists of a hollow steel cylinder, close at both ends, having an inside diameter of 700 mm and an inside length of 500mm. The cylinder mounted on a sturdy frame on ball bearings. The opening shall be closed dust-tight with a removable cover bolted in place. A detachable shelf which extends through of the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 r.p.m by an electric motor through a heavy duty reduction gear.
• Supplied complete with a tray for collection of the material.
• Accessories:
• Abrasive charge : Consists of set of 12 Nos cast iron spheres or steel spheres (Hardened steel balls) approximately 48 mm in diameter, each weighing between 390-445 gram.
  

  
  ASEW-192

  • Dorry Abrasion Testing machine:
  • BS : 812 This machine is used for determining the resistance of aggregates to wear by abrasion. Two specimens can be mounded simultaneously and then kept loaded by weight against a machined flat circular grinding surface. 
  • Suitable for operation on 230 volts, single phase, 50 cycles, A.C. supply. Fitted with starting switch.
    

    
    ASEW-193

    • Accelerated Polishing Machine, IS : 2386 (P-IV),BS 812-114
    • Consists of a road wheel having a flat periphery, and about its own axis at a speed of 320 to 325 rev/min. Rubber tyred wheel of 20 cms dia and 5 cms breadth to bear on the stone surface of the road wheel with a total load of 40 kg.
      

      
      Flexural and Abrasion Tests

      ASEW-194
      

      • Tile Flexure Strength Testing machine: IS:654 capacity 200kg. For clay roofing tiles (Mangalore pattern).
      • The apparatus consists of two parallel self-aligning cylindrical steel bearers about 40 mm in diameter. The load is applied through a third steel bearer of similar shape placed midway between and parallel to the supports. Bearing rollers can be placed at 250 or 270 mm center distance.
      • This is a double lever loading machine and the load is applied by flow of lead shot which automatically stops when the sample breaks. The load is applied at the rate of 45 to 55 kg./minute meter and the accuracy of load indication is+- 2%. Without leads shots.

       

      ASEW-195
      

      • Tile Flexure Strength Testing machine: IS: 1237. capacity 200 KG. For cement concrete flooring tiles. To ASEW-194 but for the bearing rollers of 25 mm dia and spans of 150,200 and 250 mm. The load is applied at the rate of 200 kg/min/metre. Without lead shots
        

      ASEW-196
      

      • TILE Abrasion Testing Machine:IS: 1237,1706 For Cement Concrete Flooring Tiles.
      • The abrasion testing machine consists of a replaceable grinding path fitting on to a disc rotating about its vertical axis. Suitable for operation on 230 volts, single phase, AC supply.
      • Accessories:
      • Thickness measuring device with dial gauge 0.01 mm x 25 mm travel.
        

       

ASEW-198

• Riffle Sample Divider : IS :1607, 2720; ASTM C136, D421, D422, D427, D4517, D452, D457, D806, D4318, BS:812 (part 103), 1377, AASHTO T27,T87
• Consists of a metal box fitted with a series of chutes of equal width which discharge the material alternatively in opposite directions into separate pans. The chutes of the riffle are steep enough to allow rapid flowing of the material, a. Slot width-13 mm No. of slots-14.
• Supplied complete with two pans and one scoop.
  

  
  ASEW-199

  • Riffle sample divider b. Slot width 25 mm No. of slots-16
  • Complete with two pans and one scoop.
    

    
    ASEW-200

    • Riffle Sample divider c. Slot width 50mm No. of slots-10
    • Complete with two pans and one scoop.
      

      
      ASEW-201

    • Riffle Sample divider d. Slot width 40mm No. of slots-10
    • Complete with two pans and one scoop.

    
    ASEW-202

    • Mechanical Rotating Sample Divider: IS: 1607 Consists of a trough, divided into sector, a hopper with adjustable diaphragm having six holes of 10 mm, 8 mm, 6 mm, 5 mm, 3 mm and 1.6 mm diameter and a shutter. A rotating spreader connected to the drive motor through a reduction gear turns at approx. 440 r.p.m. to distribute the sample over the trough. Suitable for operation on 230 volts, 50 cycles, Single Phase, A.C. supply.

Our company is offering Aggregate Impact & Deval Abrasion Testing Machine, which is an important instrument in construction projects; an aggregate crushing value apparatus fulfills many purposes and is highly demanded because of its precise & effective working. These are used in ceramic industry and calibration laboratories/test house.

Specifications:

Mechanical Properties of Aggregates

ASEW-185

• Aggregate Impact Tester : IS 2386 (Part IV),BS812
• Determining the aggregate impact value of coarse aggregate. Consists of a base weighing between 22-30 kg with a lower surface of not less than 30 cms and support columns to form a rigid frame work around quick release trigger mechanism to ensure an effective free fall of the hammer during test. The free fall can be adjusted through 380+-5.0 mm. The hammer is provided with a locking arrangement.
• A metal tup (hammer) weighing 13.5 to 14.0 kg, the lower end of in cylindrical shape, 100 mm in diameter and 5 cm long with a 2 mm chamfer I at the lower edge, and^ case hardened.
• Complete with a cylindrical cup, 102 mm dia x 50 mm depth, one measure 75mm dia x 50 mm deep and tamping rod of circular cross-section 10 mm in diameter and 230 mm long, rounded at one end.
  

  
  ASEW-186

  • Aggregate Impact Tester with automatic blow counter, as per IS : 2386 (P-IV)
  • Spares:
  • Automatic blow counter
  • Tamping rod.
    

    
    ASEW-187

    • Aggregate Crushing Value test apparatus : IS : 2386 (Part IV)
    • Consists of a 15 cms diameter open-ended steel cylinder, with plunger and base plate. Complete with a tamping rod of circular cross-section 16 mm in diameter and 45 to 60 cms long, rounded at one end.

    
    ASEW-188
    
    
    

    • 10% Fine Value apparatus as per IS: 2386 (p-iv) with tamping rod and measure.

    ASEW-189
    

    • Aggregate Crushing Value test apparatus IS:2386(P-iv)BS812
    • Similar to ASEW-187, but 75 mm dia cylinder. Accessories :

    Cylindrical metal measure 11.5 cms diameter and 18 cms height fitted with handles.

     

    Aggregate Abrasion Value

    ASEW-190

    • Deval Abrasion Testing machine: IS: 2386 (P-IV) For the determination of resistance of aggregate to wear by abrasion. Two hollow cylinders, closed at one end and provided with tightly fitting covers at the other end.
    • The inside diameter of the cylinder 20 cms and 34 cms depth. The cylinder are mounted on a shaft at an angle of 30 degrees with the axis of rotation.
    • The shaft rotates at 30-33 r.p.m. through a reduction gear, coupled to a motor. Suitable for operation on 440 volts, three phase, 50 cycles,A.C. Supply.
    •  
    • Supplied complete fitting with a counter and push button starter.
    • Accessories:
    • Abrasive Charge : Consists of 12 Nos. cast iron spheres or steel spheres (steel balls) hardened, approximately 48 mm in diameter, each weighing between 390-445 gram.

     

We are engaged in offering Thickness & Length Gauge, which are used in diverse applications such as soil analysis, cement & concrete industry rock & aggregate testing and ceramics. These are also used to measure sample sizes of aggregates, sand and fillers.

Specifications:

Determination of flakiness & elongation

ASEW-203

• Thickness Gauge :
  
  Constructed of heavy gauge sheet steel with chromium plating as per IS : 2386 (Part-1)

ASEW-204

• Length Gauge: IS : 2386 (Part-I) Constructed from steel, mounted on a hardwood base.

Our company is engaged in manufacturing and supplying a wide range of Specific Gravity, Density, Voids, Absorption & Bulking Testing Machines, which is available in various sizes, heights and diameters as per the clients’ specific requirements. These are manufactured of heavy gauge sheet fitted with handles.

Specifications:

Specific gravity, density, voids, absorption & bulking

ASEW-205

• Density Basket, 20 cm dia x 20 cm high fitted with galvanized wire mesh with handle. IS: 23 86 (Part III).

ASEW-206

Cylindrical Metal Measures :

 IS :2386 (Part-Ill). Made of heavy gauge sheet fitted with handles.

ASEW-207

• Metal Measures: IS: 1199
• For determining the unit weight of aggregate. Consists of one each of 10 liters and 20 ltr. Capacity fitted with handles
  

  
  ASEW-208

  • Pycnometer of about 1 Kg capacity fitted with cone, locking ring with rubber seal as per IS:2386 (Part-Ill)
    

  
  ASEW-208A

  • Density Bottles. Supplied complete with capillary vent stopper, confirms to BS 733.cap.25ml,50ml& 100 ml.
    

  
  ASEW-209

  • Sand absorption cone and tamper : Consists of a conical metal mould and a metal tamping rod having circular tamping face 25 mm dia as per ASTM C 128,AASHO.T84

We are a leading manufacturer and supplier of a wide range of Hydraulic Jacks, which is widely used in the automotive industry. The jacks are supplied complete with manually operated pumping units fitted with bourdon tube type hydraulic pressure gauge and a copper connecting tube or rubber flexible hose pipe.

Specifications:

ASEW-210

• Hydraulic Jack, Hand operated : Remote control type.
• Hydraulic jacks are of multipurpose utility i.e. application of loads while engaged in field investigation, determination of load carrying capacity of piles in the field, tensioning of wires in pre-cast structures, loading of members of any structure for deformation characteristics etc. The Jacks are supplied complete with manually operated pumping units fitted with Bourdon tube type Hydraulic pressure gauge and a copper connecting tube or rubber flexible hose pipe.
• Lift of the ram - 150 mm Pressure gauge - MASTA/WIKA (Pressure gauge have normally 200 divisions for fully capacity, e.g. 100 tonne x 500 kg divisions).
• Capacities available:
• 10 Tonne Capacity
• 20 Tonne Capacity
• 25 Tonne Capacity
• 50 Tonne Capacity
• 100 Tonne Capacity
• 150 Tonne Capacity
• 200 Tonne Capacity
  

  
  ASEW-211

  • Hydraulic Jacks, Bottle TYPE Hydraulic Lifting Jacks-Complete with integral Pumping unit. Release valve provided on the base plate. Complete with operating handle. Hydraulic lift - 150 mm and Extension Screw - 150 mm
  • All Jacks are without pressure gauge.
  • 5 Tonne Capacity
  • 10 Tonne Capacity
  • 20 Tonne Capacity
  • 25 Tonne Capacity
  • 30 Tonne Capacity
  • 50 Tonne Capacity
  • 100 Tonne Capacity
  • Accessories : Hydraulic Pressure Gauge